Skip to main content
-
If I have to use the manual loom with my Manual VY what has to be modified to fit the l67 engine?
-
If I install the 3.27 ratio without adjusting the transmission shift points, is the transmission still going to shift at the same rpm and vehicle speed as it is now?
-
If I post my LIM down Mace for porting, can I send my W2A inercooler core too so the porting is matched to the core?
-
If I purchase the 85MM Mass Airflow Meter suitable for Holden VS-VY V6
-
If I put a manual memcal into my auto VN V6, I should not worry about buying a full new ECU right?
-
If I put over head cams on my VZ alloytec, what other engine work will I have to do other then a tune?
-
If I shave the heads of my Ecotec/L67 20 thou will I have a height clearance problem if so what will I need to get to over come this problem?
-
If I turbo charge my 2009 VE SV6 alloytec to get the power I want. Is a bigger camshafts recommended, bigger than 226? I’m hoping for roughly 350-400RWKW's so roughly 437-500KW's at the engine from my calculations? I'm currently running 188.9RWHP-140RWKW.
-
If I use the Mace COMP Cam with say 1.8 rockers and stock valve springs, I would lose lift this way, but still get good results because of the longer duration right? Reason I'm asking is because I'd like to cam my car using stock springs and timing chain.
-
If I wanted to get a cam for a VT 5 speed manual V6 but it had a VY motor in it would the stage 2 VT manual cam suit my engine?
-
If I was to get a Raptor Supercharger kit to suit my VT V6 Ecotec, would I still be able to use my manifold spacers and larger throttle body?
-
If I was to go for a ls1 TB, would I have to tune the car?
-
If I were to come up to Mace to get my charger
-
If is was to go with one of your LS1 Recalibrated PCMs would i be able to simply unplug the maf sensor and remove it and the car would work fine?
-
If it’s viable maybe you guys could start stocking them for the V6 Supercharge community the company is called summit racing.
-
If the LS1 THROTTLE BODY ADAPTOR TO SUIT VN-VY V6 & VS-VY L67 is only 90mm, should I consider looking at 100mm throttle body's or is it a waste of time going that big?
-
If the rocker covers are just polished does the rats ass racing painting cost more?
-
If the valves in my VY ecotec are rooted do you stock replacements?
-
If you could tell me step by step exactly how to replace the spark plugs properly without causing any damage I would greatly appreciate it.
-
I'm looking at getting the orssom OTR for my 2010 manual SV6 SIDI Ute. I was also going to get a plenum spacer and a manifold insulator. Do you recommend the 12 mm manifold insulators? And what do you recommend in the plenum spacer?
-
In regards to returning 1.98:1 rockers for a set of 1.9:1 rockers, and keep the push rods and spacer plates. Is that correct?
-
In regards to the COMP CAMS TO SUIT HOLDEN V6 ECOTEC ad, is this the price for a stage 2 cam?
-
In Regards to the Ebay listing http://www.ebay.com.au/itm/ws/eBayISAPI.dll?ViewItem
-
In regards to the LS1 transmission rebuild kit and a bottom end rebuild kit, what brand does Mace recommend and/or what can Mace offer?
-
In regards to the PCM you guys have advertised, does that mean it’s a completely different PCM all together, or will the one I order as a replacement of my standard one be able to suit the cams and rockers? I have got a 2003 VY commodore V6 S pack auto.
-
In regards to the HIGH RATIO ROLLER ROCKERS FOR HOLDEN ECOTEC AND L67 V6, is it only half we buying or is it both sides of the block?
-
In regards to these relatively new cam packages for the VZ-VE Alloytec engines, are the factory valve springs suitable for this cam setup?
-
In regards to these relatively new cam packages for the VZ-VE Alloytec engines, would it be safe to assume reasonably versatile performance for street driving in general?
-
In regards to these relatively new cam packages for the VZ-VE Alloytec engines, what kind of labor/engine work is involved in the installation and a rough idea of what it might cost to have it done?
-
In regards to your NA mods for my car (according redbook) does 0-100 in 9.3 secs. If I did some modifications like roller rocks, CAI and re-calibrated computer, how much would that improve?