Skip to main content
-
I have got a VR BT1.5 litre and I am wondering if you could do a performance memcal for me?
Its stock internals, high flow cat and 2.5 inch exhaust, cold air intake, standard thermostat and auto.
-
I have got around 1k to spend on some extra kw's, I was thinking of "ORSSOM OTR COLD AIR INTAKE,
-
I have got the Mace Throttle bodyTB603-A5 and TB803-A1for my VN V8 fitted; only found that the cruise control will only go up to 60km? Not sure why otherwise very happy.
-
I have got the 25mm manifold insulator, do I have to move the fuel rails and other hoses etc, if yes, does this stuff come with the insulators?
-
I have had a L67 out of a VS statesman put in my VS Wagon. I purchased a memcal off Mace ages ago and went to fit it,soon as I turn the ignition to the first position the thermo fan kicks in. So I am guessing its not reading the sender. Ecotec is programm
-
I have had no success in getting my parcel. I don’t believe signature was required on this one? So I am not sure what Australia post has done with it? I don’t think anyone would have seen it/picked it up as it’s in a very secluded spot downstairs. Auspost
-
I have heard about OBD-II port and ghost cams on Just Commodores forum feedback page, is it worth to put these on a MY08 Omega?
-
I have heard great results about Mace's 10 psi pulley upgrade, am I right in thinking that if someone were to go above that 10 psi that an inter-cooler would be required?
-
I have heard Mace use to sell comp cam OE-R lifters for the ecotec and I was wondering if you know what the preload should be. I have it set to 3/4 turn as the instructions say 1/4-3/4 turn. They do seem too noisy though. Have you had any experience with
-
I have heard Mace used to sell comp cam OE-R lifters for the ecotec. Is there a bad side apart from the noise of the OE-R's?
-
I have heard stories about the 85MM MASS AIRFLOW METER For Holden VS-VY V6
-
I have heard that people are having trouble when they fit the 69mm throttle on Ecotec. Saying the mixture is too lean and gears change lower and it needs a tune with it. The memcal that comes with the kit, does that stop any of that?
-
I have just bought a VY storm ute and I am thinking about upgrading the ECU but I am facing an issue at the moment with the car surging under light throttle, I was wondering if you guys have heard anything like this before and can you suggest some modific
-
I have just installed a stage 3 Crow cam package including heavy valve springs, hyd lifters, timing chain
-
I have just purchased a brand new Cruze SRI and I'm interested in the Mace upgrade tune, my only concern is will the dealer pick up that any of this has been done when it goes in for servicing?
-
I have just purchased a factory L67 supercharger setup but no ecu, what do I need?
-
I have just purchased a powerdyne supercharger for my Ute and I was interested in ordering the crank pulley so the belt from the supercharger can line up with the crank, can Mace supply me with this product?
-
I have just purchased an automatic 2007 crewman running the alloytec engine, I intend to use it to tow a small van (900kg). From what I have read these motors lack torque for towing or torque is developed too high in the rev range for the gearing it comes
-
I have just started hearing a noise on my Sprintex Supercharger. Its on a Landcruiser 100 series 4.5 petrol. Do you have a rebuild kit for this type of supercharger?
-
I have Mace's A2A plate in my L67, is is there another charger that will fit on or only the M90.
-
I have made a mistake. I wanted to purchase the 25mm plenum spacer to suit an ecotec, instead of the 12mm version. Could I just pay the extra into your paypal and organise this ASAP?
-
I have no idea where the Power Pro Flash tuning cable plugs in? Do you have a diagram or can you let me know where to start looking.
-
I have noticed on your website something about cams I don't know much about them but is it worth doing on my car? Wanting better performance so if you have any ideas please suggest?
-
I have noticed that for boosted applications it is recommended to use a 12mm manifold insulator with 25mm plenum spacer but for my VS 4.2L I was advised to buy each of the manifold insulator and plenum spacers, is there a reason it wasn’t recommended the
-
I have ordered 3.2" pulley and hub, with 8 rib conversion pulleys. Any updates on this purchase?
-
I have pontiac G8 V6 (LY7) I want do tune for it with ghost cam sound can Mace do it for me and how much will cost?
-
I have purchased a CAI from you and its time to clean the SAAS pod filter, I'm aware that the pods are supposed to be used dry due to the MAF sensor. I was wondering how to clean the pod and still keep it as a dry pod? As all of the recharge kits availabl
-
I have purchased an inlet manifold gasket which I discovered I do not require, I have read the T
-
I have purchased manifold insulators suitable for rb25 and 2jz engines from Mace before. Do you have anything suitable for 4agze now and can you supply?
-
I have purchased other items from Mace in the past and was wondering if we can do a package deal for a chip as well as roller rockers?