Michael
- Total activity 4127
- Last activity
- Member since
- Following 0 users
- Followed by 0 users
- Votes 0
- Subscriptions 2167
Articles
Recent activity by Michael-
I've got a L67 supercharged motor. It's in a Toyota hiace. Yes it was fun getting it in and is a great motor. I'm looking for a boost upgrade for it. How much boost on the standard computer will it take. I heard you can run an XU6 chip and go to 10lb. Is
Assuming your engine is in good working order and are running on 98 octane fuel, then the most you can responsibly run is a 10psi pulley with the standard tune/computer. Any more and you would requ...
-
I've got a twin throttle body manifold with two 69mm bored out throttle bodies. How much airflow would it create?
It won’t. In fact the twin throttle body manifold would assist with reducing the pressure drop across the intake, resulting in more power.
-
I've got a VY auto ecotec, where I have machined 30 thousands off the heads which should have taken the compression to around 10:1, I’ve fitted the ultra high ratio rockers and the heads are hand ported. I've also fitted the 12mm manifold insulator and 12
Unfortunately, your current setup would require a custom dyno tune.
-
I've put a vt l67 in a series 1 vs ute just wondering which A2A intercooler kit would I need?
The intercooler kit that you would require would be for the one to suit a VN-VS. The part number for this kit is AA606, as shown in the link below. http://www.maceenginee...
-
I've upgraded factory l67 pulley and wondering what the spark plug gap spec is for the 87mm pulley upgrade?
We would recommend around a 1 to 1.1mm spark plug gap.
-
I’m extremely happy with the Inlet Insulator/Gasket it works amazing, but there’s one problem, it didn’t say anything about My A/C Compressor Brackets Not lining up right, because the inlet is spaced out further than what it is meant to be. I’m just a lit
Thanks for the great feedback. Regarding the A/C compressor bracket not lining up, I have these fitted to my BA and your right the bracket does not line up due to the 12mm spacer. My mate also has ...
-
I’m just trying to find out if the Mace rocker upgrade kit to suit the Buick engine will work with a stage 2 or stage 3 crow cam package?
Only 1.7 higher ratio rockers will work with our stage 2 or 3 Crow Cam Pack. We can supply 1.7 higher ratio rockers. The advertised 1.9 higher ratrio rockers will not fit due to excessive lift. H...
-
I’m looking at getting a cam, though I don’t want to change anything other than the cam; however I want a loud lump shaking idle.
Your best bet would be our Stage1 COMP Cams to suit V6 Ecotec (as per the ad), which should create a nice lumpy idle, as shown in the link below: http://www.youtube.com/watch?v=YwYUXsjFmCg
-
I’m looking at your stage 2 cam kits for a V6 Ecotec 3.8L and I was wondering, once installed, do they give a rougher idle? I'm looking for a performance increase as well as a notable idle sound.
The stage 2 Comp Cams cam certainly does have a noticeable lope at idle. Please see the youtube video on the link below: http://www.maceengineering.com.au/epages/shop.sf/en_AU/?ObjectPath=/Shops/ma...
-
I’m planning on putting a smaller pulley on the V6 VT with a stock L67 engine. I’m just after some information on how much psi I can put into my motor before it starts doing damage or my supercharger spins to fast and doesn't work?
On a stock motor we recommend a maximum of 10psi with 98ron fuel and the factorytune. However, considering you intend to fit a cam you will need a custom tune, in that case you will be able to run ...