Michael
- Total activity 4127
- Last activity
- Member since
- Following 0 users
- Followed by 0 users
- Votes 0
- Subscriptions 2167
Articles
Recent activity by Michael-
I want to buy a 19 psi pulley and belt to suit what's involved in it’s installation? Do I need to machine the snout but how do I go about it?
Please see our fitting Instructions; http://www.maceengineering.com.au/epages/shop.sf/en_AU/?ObjectPath=/Shops/mace/Categories/Fitting_Instructions/Boost_Upgrade Please be aware that to run a 19 p...
-
I want to buy chip/memcal for my modified VX Supercharged but i'm not sure if it will make any difference. Can you help me with this?
Given the vehicle and mods you have, then we would recommend the following memcal. https://www.maceengineering.com.au/epages/shop.sf/sec0ed575fbee/?ObjectPath=/Shops/mace/Produ...
-
I want to do a tune on a 2009 VE SV6 sidi 3.6L. I am based out of Brisbane and I can't find anyone up here that can do it for my car. I have read a little into your tune instructions with connecting the pc to the car but I don’t want to make a mess of it.
I would just like to reassure you that the process is rather easy with step by step instructions which is backed up by our support team via the phone or email. You can check out the remote tuning p...
-
I want to install a cam and headers on my VE SV6, can you tell me who you supply to carry out the work.
Depending on where you are located, we may be able to recommend a workshop who could assist (?).
-
I want to install an exhaust on my VE SV6 2010 model to make it sound tuff not droney or anything.What system do you recommend without spending too much money something under the $1000 mark?
To be honest, we would recommend that you find a system you like the sound/note off as it is a very user subjective choice (you might not like the same sound as I do). Performance wise it really de...
-
I want to know if I can get throttle body spacers or a throttle body for improved power for my 2007 Chevrolet Lumina alloytec v6 otherwise known as Holden commodore v6 in Australia and Pontiac G8 in North America.
It's not standard as the standard sized throttle body has a 64mm butterfly.
-
I want to modify my Ecotec VY. I want to get a cam, rockers springs etc. Is there a good package that you do that gives good RWKW? And how much would it cost?
Generally, we recommend only going with a cam or a set of rockers. If you're looking for the most possible power between the two then we'd recommend going with a cam upgrade instead. Assuming you'v...
-
I want to purchase a 69mm throttle body but unsure as to which one I need the VX or the VY one, there 2 different IAC one has a big end and one has a small end, the big one isn't available anymore only the small.
If you had to pick between the two then we would recommend going with a VS-VX 69mm throttle body. Our part number for this item is TB601.
-
I want to purchase a cam for my ecotec and I was told that I can only go for stage 2 as I have the 1.95 roller rockers. If its true how much is the stage 2 cam and will it sound lumpy and will it still run with the stock engine control unit?
What S2 cam are you referring to? The cams that we normally recommend for higher ratio rockers are shown in the link below: http://www.maceengineering.com.au/epages/shop.sf/en_AU/?ObjectPath=/Shops...
-
I want to purchase the cold air intake for my Nissan petrol 3L RB30 and just wondering if this will suite my car?
Considering your enquiring about the upper manifold insulator to suit an RB30 engine, if you have a standard fuel-injected version of the RB30 engine, then this item would suit. If you have either ...