Siya
- Total activity 2783
- Last activity
- Member since
- Following 0 users
- Followed by 0 users
- Votes 0
- Subscriptions 1360
Articles
Recent activity by Siya-
Your pushrods (PR601) come in 4 different sized. Is there a certain size I will need for the stage 3 cam or will any of them do?
Generally, you'd want to verify your pushrod length with a pushrod length checker at the time of your cam install, but given all our ecotec cams still have the factory base circle diameter then PR6...
-
Does Mace offer a full Power Bond pulley kit for the SIDI 3.0L engine?
We have this and the part number is PBK602
-
For the "HOLDEN SUPERCHARER BOOST UPGRADE for SUPERCHARGED V6". What’s the factory boost rated at? Some websites said 4psi some 6psi. Would running an 8psi or 9 psi pulleybe a safer option or merely a waste of money, also im looking at installing extrac
Factory boost is at 6psi. If your running your vehicle on 98RON then it will be a waste of time. If your running your vehicle on 95 fuel then the 8psi pulley is recommended regardless of extractors.
-
Hi I'm thinking of converting my holden ve v6 to at LSA superchared engine just wondering all the things I need to change in it. would I have to change engine mounts ? and would all the dash electronics still be compatible with the engine ? would my dif
We would recommend getting a hold of a wrecked VE V8 and converting everything over except for the original engine, in which case you would replace it with the LSA engine. Please note that you woul...
-
Hi I've been looking at putting a cam in my holden ve sv6 ute. I've noticed that you sell a HOLDEN VZ-VE ALLOYTEC V6 CAM PACKAGE. I was just wondering how lumpy this camp package is? Is it equivalent to a stage 2? Stage 3?
To give you an idea as to how our Alloytec cams sound, please refer to the youtube clip below. http://www.youtube.com/watch?v=c-bZmgKEaIM In regards to cam stages, these are not universal units of ...
-
Is Holden performance memcal to suit vx v6 l67 the right memcal for my 02 Monaro?
Yes, it is.
-
I have a Pontiac 2009 G8 GT 6.0L. I bought PERFORMANCE VCM OTR COLD AIR INTAKE PONTIAC G8 GT GXP L76 LS3 6.0L 6.2L V8 and its asking me to pick Manufacturer Part Number CAI836 or CAI837, which one do I pick for my car?
If you a planning on keeping your factory airflow meter then pick CAI836, if not then pick CAI837. From experience though 99% of people keep the airflow meter and order CAI836. Only customers who h...
-
I have a stock s/charged V6 VX. Could you please tell me which pulley size will best suit my vehicle? Is the 10 psi the best size or can I get away with an 11psi? Bear in mind that this is a daily driver used for both work runs and to get the kids to scho
Seeing as your car is dead standard. The max you can run is 10psi (3.4) - in conjunction with 98 octane fuel. On 95 octane fuel, the max you can run is an 8psi (3.6) pulley. With the addition of an...
-
I have a supercharged L67 in my 80's rodeo Ute, and I would like to put an intercooler on it, but the engine is really close to the firewall, so I would just like to know how much more room the plate for an intercooler take up over the standard inlet?
The intercooler plates that we use raise the supercharger vertically by 25 or 52mm, depending on the l67 intercooler kit.
-
I have a supercharged V6 VY commodore S running a nine psi pulley, memcal chip, cold air intake and extractors back exhaust. I recently installed msd blaster coils and it has developed a very small misfire at mid range to high revs, I was wondering if you
We would recommend sticking with the factory spark plugs, but closing the spark plug gap down to 1mm.